Hdt (Hardware Detection Tool)

From Syslinux Wiki
(Redirected from Hdt)
Jump to: navigation, search


The project used to have its own website, now archived.

This document might be partially outdated.


What is HDT ?

HDT (for "Hardware Detection Tool") is a Syslinux com32 module designed to display low-level information for any x86 compatible system.

HDT can inspect multiple subsystems:

  • CPU (via cpuid)
  • PCI
  • DMI
    • Memory modules
    • BIOS
    • Motherboard
    • IPMI base board
    • Chassis
    • Batteries
    • CPU
  • Disks (work in progress)
  • Syslinux
  • Linux Kernel modules needed by this host
  • PXE environment
  • VESA
  • ...

Release

Current stable release is 0.3.3 0.5.2.

Current development version is 0.3.4 in the main Syslinux git repository.

Download

HDT is included in the official Syslinux distribution archives.

History

Syslinux 3.74 features HDT 0.2.7.

Syslinux 3.75 features HDT 0.2.7 with a fix to prevent hard lock during pci detection.

Projects known to use HDT

  • Mandriva Linux since 2009.1 (no longer active since 2015)
  • Ultimate Boot CD since version 5.0
  • Parted Magic since 0.4.0
  • Recovery Is Possible since 8.0 (no longer active since 2012)
  • Many others

How can I try HDT ?

Since Syslinux 3.74, HDT is available in the Syslinux archive under the "com32/hdt" directory.

HDT is a com32 module that requires syslinux 3.74 or later. As every com32 module, it can be booted as a kernel like:

LABEL hdt
 KERNEL hdt.c32

Testing using kvm/qemu

Since qemu 0.9.0, it is possible to boot a virtual machine while using a local directory as a local pxe server. This allows a local PXE booting without needing a complete infrastructure (dhcp/tftp).

  • Install kvm/qemu.
  • Setup you environment by creating a local pxe directory like "~/pxe".
  • In this pxe dir, create another directory, named "pxelinux.cfg".
  • Within the "pxelinux.cfg" directory, create the following configuration file named "default":
DEFAULT hdt
PROMPT 1
TIMEOUT 5
LABEL hdt
 KERNEL hdt.c32
  • Copy the "pxelinux.0" (and "ldlinux.c32") file(s) from the Syslinux archive to the "~/pxe" dir.
  • Copy the hdt.c32 file (and the relevant library modules) in the same directory.
  • Create a dummy disk file with
dd if=/dev/zero of=~/pxe/dummy.img bs=1M count=5
  • Start qemu/kvm to use that local configuration:
kvm -hda ~/pxe/dummy.img -net nic -net user -boot n -tftp ~/pxe -bootp /pxelinux.0


Menu mode

The menu mode will try to do some best effort to manage the little space in which we display so much information.

Screenshots taken on HDT 0.2.6.

Main menu:

Hdt-menu.png

Cpu mode:

Hdt-menu-cpu.png

Starting memtest

Under the memory menu, it is possible to start memtest. To make it successful, you have to:

  • Download memtest
  • gunzip it
  • Setup in your current Syslinux configuration file an entry like
LABEL memtest
 LINUX memtest86+-2.11.bin

Make sure to use the keyword "LINUX", not "KERNEL"!

Then, when selecting the memory test from the memory submenu, the "memtest" label will be launched.

The label name could be changed using the "memtest=<label>" boot option of HDT. The default value is set to "memtest".


How do I configure HDT ?

HDT can be configured by APPENDing parameters, as described in the following sections.

pci stuff

HDT requires very little configuration. To improve the PCI reporting, copy "pci.ids" and "modules.pcimap" in a directory. By default, hdt will search for these files in the root dir of the boot device. If you want to override the directory you can use the following parameters:

  • modules=your_path/modules.pcimap
  • pciids=your_path/pci.ids
  • memtest=label_name

This can be configured as:

LABEL hdt
 KERNEL hdt.c32
 APPEND modules=images/modules.pcimap pciids=images/pci.ids memtest=mymemtest

The "pci.ids" file can usually be found in the "/usr/share/" directory of a Linux System or just download it from sf.net.

The "modules.pcimap" file is usually available in the "/lib/modules/`uname -r`/" directory of your Linux system.

Warning! When HDT is used with ISOLINUX, the file name must be in an "8.3" format. So if your file is named "modules.pcimap", then the parameter given to HDT must be: "modules=path/to/modules.pci".

If these files are not available, HDT will generate some information messages to warn the user.

The memtest=<label> option allows users to override the default entry name in the current config file of Syslinux. The default value is set to "memtest".

CLI mode

HDT supports two modes: a menu system and a CLI (command line interface). The menu system is enabled by default. To enable the CLI mode, just append "nomenu" at startup time like in:

LABEL hdt
 KERNEL hdt.c32
 APPEND nomenu


Syntax of the CLI

This syntax may change in the future.

The main menu displays a "hdt> " prompt indicating the top menu.

Other submenus exist: pci, dmi, cpu, kernel, pxe, syslinux. These topics will be discussed later.

The help command shows the available commands:

  • clear  : obviously, clear the screen
  • help  : this help ;o)
  • show  : the command to display items
  • pci  : to enter the PCI mode
  • dmi  : to enter the DMI mode
  • cpu  : to enter the CPU mode
  • kernel : to enter the kernel mode
  • syslinux : to enter the syslinux mode
  • vesa  : to enter the vesa mode
  • exit  : to return to the top menu

Note that it is possible to use "show" in order to obtain a summary of the given mode, like in:

 hdt> show pci
 PCI: 17 devices detected                   
 PCI: Resolving names
 PCI: Resolving class names
 PCI Resolving module names                
 PCI                                        
  NB Devices   : 17         
 hdt> 
  

or:

 hdt> show dmi     
 DMI Table version 2.3 found
 Available DMI modules: base_board bios chassis memory bank<bank_number> cpu system          
 hdt> 

The "show dmi" command will display the version of the DMI table and the available modules.

Other examples:

 hdt> show cpu                                              
 CPU                        
  Manufacturer :  Intel                     
  Product      :  Intel(R) Pentium(R) D CPU 3.00GHz                              
  Features     :  3000 MhZ : x86_64 64bits SMP
 hdt> 


 hdt> show pxe                              
 PXE                        
  PCI device no: 15         
  Manufacturer : Broadcom Corporation              
  Product      : NetXtreme BCM5721 Gigabit Ethernet PCI Express                  
  Addresses    : 192.168.3.8 @ 00:13:72:3b:ce:85
 hdt> 


 hdt> show syslinux 
 SYSLINUX                            
  Bootloader : PXElinux              
  Version    : PXELINUX 3.74 pre1-110-g37bfb1c
  Version    : 842      
  Max API    : 35     
  Copyright  : Copyright (C) 1994-2009 H. Peter Anvin                
 hdt> 


 hdt> show kernel                                  
 Kernel modules                                                                  
 (intel-rng | iTCO_wdt) # (piix | ata_piix) # i2c-i801 # tg3 # sisfb #
 hdt> 


 hdt> show vesa
 VESA
  Vesa version : 3.0
  Vendor       : XGI Technology, Inc.
  Product      : Volari Z7
  Product rev. : 1.02.04
  Software rev.: Y 
  Memory (KB)  : 16384                      
  Modes        : 32
 hdt> 


Summary

The "show summary" command reports a global summary of the current host:

 hdt>show summary
 CPU
  Manufacturer :  Intel
  Product      :  Intel(R) Pentium(R) D CPU 3.00GHz
  Features     :  3000 MhZ : x86_64 64bits SMP
 System
  Manufacturer : Dell Computer Corporation
  Product Name : PowerEdge 850
  Serial       : XXXXX
 Bios
  Version      : A02
  Release      : 10/12/2005
 Memory Banks
  bank 00      : 512 MB DDR2@533 MHz
  bank 01      : 512 MB DDR2@533 MHz
 PCI
  NB Devices   : 17
 PXE
  PCI device no: 15
  Manufacturer : Broadcom Corporation
  Product      : NetXtreme BCM5721 Gigabit Ethernet PCI Express
  Addresses    : 192.168.3.8 @ 00:13:72:3b:ce:85
 Kernel modules
 (intel-rng | iTCO_wdt) # (piix | ata_piix) # i2c-i801 # tg3 # sisfb #
 hdt> 


PCI mode

From the main menu, type "pci". The prompt changes to "pci> ". The available commands are:

show list

The "show list" command reports the available pci devices like in:

 pci> show list
 21 PCI devices detected
 01: Intel Corporation E7230/3000/3010 Memory Controller Hub
     # Host bridge               # Kmod: unknown
 
 02: Intel Corporation E7230/3000/3010 PCI Express Root Port
     # PCI bridge                # Kmod: unknown
 [....]
 12: Intel Corporation 82801G (ICH7 Family) IDE Controller
     # IDE interface             # Kmod: piix | ata_piix
 [....] 


The first numerical field (01, 02 or 12 in this example) represents the PCI device number followed by the vendor and product names.

The second line displays the device class and the associated kernel module. If no module matches this pci device, the kernel module (Kmod) is reported as unknown. If the device matches one or more kernel modules, the Kmod field shows their name, piix or ata_piix in this example.

show device <number>

The "show device <number>" command reports more detailed information on the selected pci device. Let's see a report for the PCI device number 12 from the previous example:

 pci> show device 12
 PCI Device 12
 Vendor Name   : Intel Corporation
 Product Name  : 82801G (ICH7 Family) IDE Controller
 Class Name    : IDE interface
 Kernel module : piix | ata_piix
 Vendor ID     : 8086
 Product ID    : 27df
 SubVendor ID  : 1028
 SubProduct ID : 01b6
 Class ID      : 01.01.8a
 Revision      : 01
 PCI Bus       : 00
 PCI Slot      : 31
 PCI Func      : 01
 pci> 

The output is pretty obvious, no need to say more about it except about the pxe stuff. If the current device has a running pxe rom, its pxe information will be displayed:

 Mac Address   : 00:13:72:3b:ce:85
 PXE           : Current boot device

If the device has a valid IRQ, an "IRQ: <irq>" line is displayed.

show irq

HDT can show IRQs set to some PCI devices. Most PCI devices do not really have a legacy IRQ. Only valid IRQs (>0 & <255) are shown.

 pci>show irq
 17 PCI devices detected
  IRQ : product
  -------------
  11  : Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1
  05  : Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express
  03  : Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express
 pci> 

DMI mode

Inside the dmi mode, "show list" displays the available modules.

 dmi> show list
 Available DMI modules: base_board bios chassis memory bank<bank_number> cpu system  

Note that only available modules will be displayed by this command. If your system doesn't have a battery, the battery module will not be reported.

To display the content of each module, use "show <module>":

 dmi> show system
 System
 Manufacturer : Dell Computer Corporation
 Product Name : PowerEdge 850
 Version      : Not Specified
 Serial       : XXXX
 UUID         : XXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXX
 Wakeup Type  : Power Switch
 SKU Number   :
 Family       :
 dmi> 

Nothing more to say except about the memory module.

memory display

The "show memory" command will display the status of each memory bank reported by the DMI table.

 dmi> show memory
 Memory Banks
  bank 00      : 512 MB DDR2@533 MHz
  bank 01      : 512 MB DDR2@533 MHz
  bank 02      : Free DDR2@533 MHz
  bank 03      : Free DDR2@533 MHz
 dmi> 

As reported by the command, to have more details of a given memory bank, use "show bank<bank number>".

 dmi> show bank1        
 Memory Bank 1          
 Form Factor  : DIMM        
 Type         : DDR2   
 Type Detail  : Synchronous
 Speed        : 533 MHz
 Size         : 512 MB 
 Device Set   : 1      
 Device Loc.  : DIMM1_B
 Bank Locator : Not Specified
 Total Width  : 72 bits
 Data Width   : 64 bits    
 Error        : Not Provided
 Vendor       : C100000000000000
 Serial       : XXXXXXX
 Asset Tag    : XXXXXXXXX
 Part Number  : XXXXXXXX
 dmi> 

IPMI base board display

Since 0.2.6, HDT can detect whether an IPMI BMC is present; if it is, it displays the interface type, the version and its address.

 dmi> show ipmi
 IPMI
  Interface Type     : KCS (Keyboard Control Style)
  Specification Ver. : 1.5
  I2C Slave Address  : 0x10
  Nv Storage Address : 0
  Base Address       : 0000000000000CA8
  IRQ                : 0
 dmi> 


CPU mode

Inside the CPU mode, use "show cpu" to display the cpu information:

 cpu> show cpu
 CPU 
 Vendor    : Intel
 Model     : Intel(R) Pentium(R) D CPU 3.00GHz
 Vendor ID : 0    
 Family ID : 15                               
 Model  ID : 4                                
 Stepping  : 7 
 FSB       : 800 MHz
 Cur. Speed: 3000 MHz
 Max Speed : 3800 MHz
 Upgrade   : ZIF Socket
 SMP       : yes     
 x86_64    : yes       
 Flags     : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
 Flags     : cmov pat pse_36 clflsh dts acpi mmx sse sse2 ss
 Flags     : ht acc nx lm                                            
 cpu> 

Kernel mode

The kernel mode features the "show list" command that displays, for each hardware category, the needed kernel modules.

 kernel> show list
 Mass storage controller : piix ata_piix
 Network controller : tg3
 Display controller : sisfb
 Bridge : intel-rng iTCO_wdt
 Serial bus controller : i2c-i801
 kernel> 

PXE mode

The PXE mode displays information about the pxe environment.

 pxe> show list                                                
 PXE                                                           
  PCI device no: 15                             
  Manufacturer : Broadcom Corporation                          
  Product      : NetXtreme BCM5721 Gigabit Ethernet PCI Express
  Addresses    : 192.168.3.8 @ 00:13:72:3b:ce:85
 pxe> 

Syslinux mode

The Syslinux mode displays the current syslinux versions:

 syslinux> show list
 SYSLINUX              
  Bootloader : PXElinux          
  Version    : PXELINUX 3.72 3.72
  Version    : 840
 Max API    : 30                                    
  Copyright  : Copyright (C) 1994-2008 H. Peter Anvin
 syslinux> 

VESA mode

The vesa mode displays a synthesis of the vesa configuration:

 vesa> show list
 VESA
  Vesa version : 3.0
  Vendor       : XGI Technology, Inc.
  Product      : Volari Z7
  Product rev. : 1.02.04
  Software rev.: Y 
  Memory (KB)  : 16384
  Modes        : 32                               
 vesa> 

In this example, the vga card supports 32 video modes. To display them, use "show modes".

Note that "Kernel mode" is the value requested by the "vga=" command line for a linux kernel.

 vesa> show modes
  ResX x ResY x Bits : Kernel Mode : Vesa Mode
 ---------------------------------------------
   800   600      4       770        0x0102
   640   480      8       769        0x0101
   640   400      8       768        0x0100
   800   600      8       771        0x0103
  1024   768      4       772        0x0104
  1024   768      8       773        0x0105
  1280  1024      8       775        0x0107
  1600  1200      8       816        0x0130
  1600  1200     16       817        0x0131
   320   200     15       781        0x010d
   320   200     16       782        0x010e
   640   480     15       784        0x0110
   640   480     16       785        0x0111
   800   600     15       787        0x0113
   800   600     16       788        0x0114
  1024   768     15       790        0x0116
  1024   768     16       791        0x0117
  1280  1024     15       793        0x0119
  1280  1024     16       794        0x011a
   320   240      8       818        0x0132
   400   300      8       819        0x0133
   512   384      8       820        0x0134
   320   240     16       821        0x0135
   400   300     16       822        0x0136
   512   384     16       823        0x0137
   320   200      8       824        0x0138
   640   400     16       825        0x0139
   640   480     32       826        0x013a
   800   600     32       827        0x013b
  1024   768     32       828        0x013c
  1280  1024     32       829        0x013d
  1600  1200     32       830        0x013e
 vesa>


Roadmap

Release 0.3.0

Release 0.3.1

Release 0.3.2

Release 0.3.3

Release 0.3.4

  • Fixing int10/13 conflict
  • Improving menu's layout to maximize display usage
  • Adding more external benchmark/diagnose tools (cpu/disks/...)
  • Adding more Fn keys (F1-F12)
  • Memory detection fall-back to dmi type 6 when type 17 isn't available
  • Adding filesystem detection
  • Adding mbr detection (grab info at (older) [1] or (newer) [2] )

Release 0.4.0

  • Adding a saving inventory feature
  • Adding IPMI

Development

The development of HDT is here: http://git.zytor.com/users/erwan/hdt.git

Additional changes could be merged directly into the main Syslinux git repository.

Mailing List

You can subscribe to the mailing list and/or read the archives.

Ideas

The following ideas represent possible new features for HDT. If users report which ideas they really need, priorities to develop items could change ;o)

Lua Scripting

HDT currently detects hardware and generates an output using a menu or via a CLI. It could be interesting to add lua support to manage scripting. It could be possible to load a file that describes items that the user wants to detect.

Saving reports

Current versions can't save a report as we can't reach a writable storage. When using PXELINUX, we can imagine using a tftp put method. Using GPXELINUX, we can imagine using some http/ftp put methods.

Improving disks detection

Implementing a simple IDE stack would help in detecting PATA & ATAPI devices. Detecting SATA devices would require implementing specific drivers. The Coreboot project features some; why not doing some teaming on that?

Implementing SMART

Once the previous items would be complete, it could be possible to add a smartmontools-like feature to display smart status of devices.

Adding IPMI

IPMI could give HDT more information about the current hardware like sensors, etc... While using the "open" interface, we can reach the local BMC, but sounds as it needs a lot of code.

Adding VPD

Virtual Product Data displays the following: BIOS Build ID, Product Name, Box Serial Number, Motherboard Serial Number, Machine Type/Model.

Detecting Disk's Partitions

Title is pretty obvious ;o)

Adding more benchmark/diagnose tools

For every kind of component, it could be possible to launch a benchmark/diagnose tool. UBCD has many of them; why not trying to load some from both menu and CLI mode.